Friday, July 6, 2012

Protected Cruiser scratchbuilt

     I haven't posted on this build as I was doing it, I didn't want to bore everybody with another, very similar, series of step-by-step articles. In this post I will point out the things that I did different and my reasons for doing so. I started out with another blue-board hull and added a lower section that has a distinct "tumblehome" ( the inward leaning of the lower hull, I have no idea why it is called tumblehome) to get a more exotic look. From there it was a pretty standard build except that I kept this one in sub-assemblies until the very end. This made things much easier as I could work on one bit while another was drying and it made handling the model far less fiddly.

     I hope you enjoy this as much as I did, I think a colonial gunboat is in the offing.

the major components build and test-fitted together



the techniques  used were the same as I used in building the Armored Cruiser 
(scroll down almost to the bottom of that page to find the posts on that build)

the sub-assemblies unassembled, I planked the deck before I added the hull plates, 
that way I could sand the edge of the planking and the side of the hull at the same time, 
I did forget to inscribe the planking detail beforehand, a costly mistake, 
for planking I used hard 1/32 balsa in a 4" wide sheet,
I scribed it with a hard sharp pencil and a straight-edge

hinges and a door handle; I couldn't resist adding a few little details
the card-stock was coated in a thinned mixture of glue and water
 to harden it and smooth the surface for painting

then it was "rivet-time",
 the pink is easy to see but difficult to cover with paint

all that rivetty goodness, 
one day I hope to grow up and have the nerve to apply them one at a time from cut stock,
 like Col. O'Truth, my hero and inspiration

more little details, 
a sighting hood on top of the turret and a hinge on the rear door panel

at times I went a little crazy

a deck hatch from wood discs and paper

after painting I put the parts together to check the look,
the yellow was far less overwhelming than on the Armored Cruiser

a significant gap had worked its way into the joint between the forecastle and the lower hull 
(this must be a flaw in the manufacturing process, I never make mistakes, ever, no really, I don't)
this would requires some tricky work later to correct

the colors, I chose a dark gray rather than black
the previous build showed that the black was a bit overpowering

sometimes I get a little sloppy when cutting the foam that makes up the core of the models, 
this means gaps, gaps must be covered
so like a real ship I used joining plates to attach the con to the hull,
these act like moldings in a modern house by concealing the unsightly gaps that the workmen leave between vertical and horizontal surfaces

thin strips of card. folded along a straight-edge. and then cut to length, 
these were fitted to the con....

...........and adjusted into place while the glue was still wet,
in this picture you can see my fix for the mis-fit between the upper and lower hull sections,
 I added more joining-plates to cover the gap (the white strip that runs along the side of the hull, below the port-holes) again simply strips of card, carefully positioned and glued in place

after rivets and paint the con was test-fitted again

the strips neatly concealed the unsightly gaps

after ensuring a tight fit I glued the con down, 
a thin bead of the ever-present Titebond glue

after carefully positioning the con the edges were tamped-down with the tip of a paintbrush handle
to ensure a good bond and no gaps (if you look at the lower portion of the picture you can see the joining-plate covering the hull gap, it has been riveted and painted)

the glue that oozed out was cleaned up with a wet paintbrush

the smokestack was the next step, this was too much glue,
 it oozed out everywhere, requiring a lot of clean-up

the deck-hatch, ready to install

and there it is

ready for trial runs, the armaments have not been properly fixed to the hull yet

Count Nakimoff likes his new ship

3/4 shot
  
bow

top-down

stern view 

side view


      There you have it, a quick build as I am becoming more confident and spotting ways to save time during the building process. All that remains are railings and boats.

4 comments: